Safewatch quickconnect plus manual

The system must be disarmed. Month Month The current month will display. Enter the 2-digit month designation i. Press [ADD] to accept the entry and continue to the day selection. If this feature has been programmed, the system will provide the appropriate voice messages and any system beeping sounds indicating the status of the security system over the phone line. Page Speaker Phone Feature Do not use the speaker phone as the only telephone in your home since in some special cases the speaker phone is not functional.

Establish and regularly practice a plan of escape in the event of fire. The following steps are These secondary users are identified by "user numbers" when their codes are assigned. You can assign up to 6 user codes 2-digit user numbers The keypad sounds a single beep every 45 seconds as a reminder that the system is in the Test mode. Page Trouble Messages If the condition persists, notify your service company.

Low Bat Accompanied by a once-per 45 seconds beeping at the keypad, indicates a low no zone no. Do not slam sensor-protected doors or windows.

Page 36 It is your responsibility to make sure that your system is in good working order. It's easy to test your system; just refer to your owner handbook or call and follow the simple instructions.

If you find that a part of your system is not working properly, call ADT at to request repair service. Page Servicing Information It must be returned to the factory or an authorized service agency for all repairs. Arranging some kind of regular service program with him is advisable. Previous Page. Next Page. The Installation and Setup Guide contains full descriptions for all data fields. To Load a Default Set: 97 Enter a number corresponding to the selected default table See the Installation Instructions for the default tables.

If Safewatch QuickConnect Plus is armed by RF button key fob , a confirmation ding occurs immediately after arming regardless of field 38 settings. If Safewatch QuickConnect Plus is disarmed by RF button key fob , additional disarming confirmation ding occurs immediately after disarming and is longer than arming confirmation ding. If fewer than 24 digits entered, pressing 6 advances to the next field. System will display "Entering Program Mode". Notes: 1. If 98 was previously used to exit programming, the first method shown above must be used to re- 6 enter the program mode 2.

To Program the Data Fields: 1. Press [ ] followed by the desired field number e. The keypad beeps three times after entering data, then displays the next data field in sequence. For phone number and account number fields, press [ number of digits is entered. To view data entered in field, press [ ] plus the field that you wish to view e. The system will beep three times and data programmed for that field will be displayed to the right of the field number. The system will scroll through the data for longer numbers and a beep will sound after each number is displayed or three times after the final digit is displayed.

To delete an entry, simply press [ and account number fields Interactive Menu Modes: There are six interactive menu modes as listed below. To enter these modes, first enter Program mode. While in Program mode, press [ 6 56 Enhanced Zone Programming For programming zone characteristics, report codes, etc. For entering transmitter serial numbers 6 84 Assign Zone Voice Descriptors For assigning voice descriptors to zones 6 85 Record Custom Voice Descriptors For phone number 6 44, 88 and 6 6 6 ] plus the mode number desired e.

Page 3: Data Fields. Enter 0 if you are not selecting a default table. If is used to exit 6 programming mode, system must be powered down, then press [6] and [ ] within 50 seconds of power up to re-enter programming mode. Enter 0,0 if no daylight savings time used. Page 4: Zone Sounds And Timing. If the selection is not valid the control will emit a single long beep indicating that the selection has been rejected.

The control replaces the selection with the default value "60", which is displayed on the keypad, and advances to the next field. SIA: Must be set to a minimum of 45 seconds. The control replaces the selection with the default value "30", which is displayed on the keypad, and advances to the next field. The entry delay must be set to a minimum of 30 seconds. SIA: The entry delay must be set to a minimum of 30 seconds. If Safewatch QuickConnect Plus is armed by RF button key fob , a confirmation ding occurs immediately after arming regardless of field QuickConnect Plus is disarmed by RF button key fob , additional disarming confirmation ding occurs immediately after disarming and is longer than arming confirmation ding.

If Safewatch. Page 5: Dialer Programming. In fields , , enter 4 to 10 digits. If only 3 digits used, pressing 6 advances to the next field. To clear entries from field, press or Examples: For Acct.

UL This option is not for use in UL installations. Primary Phone Number Enter up to 20 digits; Do not fill unused spaces. If fewer than 20 digits entered, pressing 6advances to the next field.

To clear entries from field, press Secondary Phone Number Enter up to 24 digits; Do not fill unused spaces. Honeywell Lynx Plus User Manual. This is the Lynx keypad that is not a touchscreen. Safewatch QuickConnect User Manual. This is the older version similar to the lynx plus keypad compatible products are available here.

This keypad has the blue section around the keys. This is the first Lynx keypad. Simon XT 2 User Manual. The second generation Simon XT does not have a cover over the keys and is less boxey looking.